Radio-frequency conductor-type location controllerClick on the picture to zoom in.

PRODUCT SPECIFICATIONS

LISEN-RF-100

Radio-frequency conductor-type location controller

Radio-frequency-guided-guided-place control, radio-frequency-guided-stage control

01

Classification: Radio-frequency conductor

02

Check configuration based on field work

⁇ Return to radio frequency conductor class

TECHNICAL SPECIFICATIONS

Technical specifications

LISEN-RF-100

Check the specifications against your operating conditions and use the selection tables to confirm your order configuration.

View selection tables ↓
ModelLISEN-RF-100
Measurement principleRadio-frequency conductor: Spectrums and canisters form an electric mask, a conductor change trigger when the material is close to the object, using adhesive three-end shielding techniques to overcome the misalignment of the mounted material
Switching actionPoint switch output (high or low, set on site), non-continuous measurements
Probe typeInsulation pole (hard pole) / Full insulation cable (soft cable) / tablet (stowage walling)
Probe lengthBar 0.3–3m / Cable 1–20m (Specify when ordering)
Sensitiveness0.5–1000pF Sustained Adjustable (in situ level/key marked)
Repeatability±1mm
Delay Settings0–30s Adjustable
Process medium temperature-40–+200℃ (high-temperature type to +450℃ with dispersed heat tablets/ pottery insulation)
Ambient temperature-40~+70℃
Operating pressureConstant pressure –4.0MPa (high pressure 10MPa Optional)
Probe material316L stainless steel / 304 / Harsh C276 / titanium (Optional)
Insulation materialPTFE / PEEK / ceramic (High-temperature type)
Process connectionG1 / G1½ / 1NPT thread / DN50–DN100 flange (PN1.0–4.0)
Output signalVoltage-free dry contact SPDT (5A/250VAC)/ NAMUR Intrinsically safe signal / transistor output (Optional)
Power supply24VDC / 220VAC (optional) / 24VAC
Status indicatorLED power supply/ Alarm / normal tri-state instruction
Ingress protectionIP65 / IP66 (Junction box)
Explosion protection markingEx d II C T6 Gb flameproof / Ex ia II C T4 Ga Intrinsically safe (Optional)
Applicable standardsGB/T 28474 / JB/T 12597 / GB 3836.1
Suitable mediaPowder, particles, slurry, foams, sticky liquids, conductive and non-conductive materials (dielectric constant ≥1.5)
Typical applicationsHigh silos Alarm, powder silos full of protection, sewage tank pump outlinks, acid tank spillproof flow, fly ash/cement/food spot control

Product selection

LISEN-RF-100
Probe type
CodeProbe type
R1Insulation hardbar (≤3m)
R2Full insulation cable (≤20m, deep/ large tank)
R3Plankted (condensary wall adhesion)
Probe length / measuring range
CodeProbe length / measuring range
L10.3m / 0.5m
L21m / 1.5m
L32m / 3m
L4Cable 5–20m (Specify when ordering)
Switching action
CodeSwitching action
A1High Alarm (full)
A2Low Alarm (negative empty)
A3High + low double scout.
Pressure rating
CodePressure rating
P1Constant pressure / PN1.0
P2PN2.5
P3PN4.0
P4PN10.0 (high pressure type, Specify when ordering)
Probe / insulation material
CodeProbe / insulation material
M1316L detector + PTFE insulation (Standard)
M2316L Probe + PEEK Insulation (resilient)
M3Haq (C276) + PTFE
M4Ceramic insulation (high temperature 450℃)
Process connection
CodeProcess connection
F1G1 / G1½ / 1NPT Thread
F2DN50 / DN80 Flange
F3DN100 Flange
Output signal
CodeOutput signal
O1Voltage-free dry contact SPDT (Standard)
O2NAMUR Intrinsically safe signal (with security fence)
O3NPN/PNP transistor output
Power supply
CodePower supply
S124VDC (Standard)
S2220VAC
S324VAC
Explosion protection marking
CodeExplosion protection marking
X1Non-Ex
X2Flameproof Ex d II C T6 Gb
X3Intrinsically safe Ex ia II C T4 Ga

Confirm specifications and ordering options

Contact us with the measurement target, operating conditions, and installation requirements to confirm your configuration.

Contact us
LISEN-RF-100 RF Admittance Level Switch