PRODUCT TECHNOLOGY

- It's a heat resistance.

Operating principle

- Thermal resistance in a suit. - The working principles.

Using Pt100 platinum resistance as a temperature element, the electrical resistance value at 0 ℃ is 100 times, temperature coefficient α = R(t) = R (0) [1 + At + Bt² + C (t-100) t³] (t< 0℃ time) where A = 3.9083×10³ / °C, B = -5.775×10⁷ / °C, C = -4.183×10¹² / °C, R (0) = 100 times (Pt100). The equation is the standard basis for temperature-to-temperature conversion within -200 ~ +850 ℃ of the international thermostat ITS-90. Thermal resistance is based on the three-axis squeeze process: 316 L / 310 S / Inc

  1. 01

    00385. Temperature-temperature resistance meets the IEC 60751 standard Callendar-Van Dusen equation:

  2. 02

    2-wire · Two leads carry excitation current and the measurement signal · Lead resistance is not compensated · Suitable for short runs with modest accuracy requirements.

  3. 03

    3 Line 1 root power + 2 sample, automatic compensation * partial removal of wire resistance * mainstream industrial site, * assembly assembly

  4. 04

    4 Line + 2 current + 2 voltage, full bridge + total debunking of the lead + exposure to resistance + high accuracy measurement, key control points

Thermal resistance support in accelerator

Provide survey missions, media and installation conditions and obtain product configuration advice.

Contact us
· Technical Note

TECHNOLOGY & APPLICATION

Understand the principles, the exact selection.

From measurement principles to field applications, the technical features and selection elements of accelerator-based thermal resistance are understood.

01

TECHNICAL GUIDE

Overview

(Mineral Insular Research Temperature Detector, MI-RTD or ArmouredRTD) is a new temperature sensor manufactured using an integrated mineral insulation process. Temperature component (Pt100/Pt1000), insulation material (high-purity magnesium oxide Mgo powder) and metal shielding ( 316L/310S/Inconel)

  1. 01

    It's formed in diameter by a special pull process, which is tightly compacted and sealed.

Φ 1.0 ~Φ 8.0 mm Soft thermocrystolic cables are the most structured, responsive and life-long product form of thermal electrical resistance family.

Thermal resistance originated from the temperature detection needs of the British military-industrial nuclear reactors in the 50 of the last century and was initially used for core temperature monitoring of nuclear reactors, which then spread to high-reliability industrial areas such as aviation, space, petrochemicals and electricity. Over the past 70 years, IEC 60751 international standards, ASSTME 1137 and JB/T8622 national standards have evolved into multi-standard systems and become essential components of temperature measurement for modern industrial processes.

Main technical characteristics

General description · Serial number / CharacteristicsCross-reference
Serial numberCharacteristics
1MI Integration: Temperature Component + Mgo Insulation + Metals Cover Layer Integration
2Bendable: Minimum curve radius 5x exterior, installed around complex curves
3Response speed: ⁇ 3 mm specification t63 response time only 1~3 s
4High pressure resistance: metal shield resistance 30~100 MPa, suitable for high pressure containers
5Resisting high: intensifies Mgo buffer, more seismic than assembly heat and electrical resistance
6Measurement accuracy: A level ± 0.15 °C, 1/3 DIN B ± 0.10 °C
7Temperature range: -200 ~ + 850 °C (Pt100 standard)
8In situ indents: end-ends can be processed into more finer measurement ends, increasing response
02

MEASUREMENT PRINCIPLE

Operating principle

2.1 Pyramid resist temperature properties (IEC 60751)

Using Pt100 platinum as a temperature element, the electrical resistance value at 0 °C is 100 times, temperature coefficient = α

  1. 01

    00385. Temperature-temperature resistance meets the IEC 60751 standard Callendar-Van Dusen equation:

Measurement formulaClick to see the big picture
R(t) = R(0) · [1 + At + Bt2 + C (t-100) t3 (t<0°C)
Measurement formulaClick to see the big picture
of which A = 3.9083 × 10 � 3 /°C,B = -5.775 × 10 � 7 /°C,C = -4.183 × 10 � 12 /°C,R( 0 ) = 100

Ω( Pt100 . The equation is an international thermometer ITS-90 Medium -200 ~ +850 ℃ Standard basis for temperature-retardation conversion within range.

2.2 Litigation and compensation for errors

2.3 MI Integration rationale

Thermal resistance is based on the "trixyxy" squeeze process.

1 In the metal tube ( 316 L / 310 S / Inconel) penetrators into Pt Retard cores;

Filling of high-purity magnesium oxide powder (Mgo ≥ 99.5%) between the metal tube and the electrical resistance core;

MGO is decontaminated by multi-channel insulation + mid-fire, and the metal tube walls are closely bound to the electrical resistance core;

End-end electrical resistance and lead wires are sealed with arc or laser welding, and end-port welding with thermal sealing caps;

Corporate structure achieved

1 Extreme electrical insulation of electrical resistance and shell (Mgo); 2 Heat transfer efficiency (MGO) 30 W/, metal casings decrypted; 3 High mechanical strength (metal shield resistance); 4 Resilient (MGO in a dense buffer).

2.4 Workflow

Motion of work · Linear / StructureCross-reference
LineStructureCompensation for errorsApply scene
2 LinedOnly 2 strings, with measurements and currentsIt's not enough to compensate for the electrical resistance.Precision requires a low degree of closeness measurement
3 Lined1 root power + 2 root sampling, automatic compensationPartial removal of wire resistanceMainstream industrial site, plastering
4 Lined2 currents + 2 voltage, full bridge methodTotal debacle + exposure resistanceHigh precision, key control points
Motion of work . Step / ActionCross-reference
StepsActions
①On-site temperature measuring end of Pt resistance ⁇ resistance value R(t) changes with temperature
②Measuring the output of the MV level signal sent through 3/4 line
③Linear processing of transmitters 4-20 MA / Hart / bus output
④DCS / PLC Receive Show Temperature / Alert / Chain Control
⑤Temperature limit, poach, trigger sound light alert, + emergency parking.
⑥Pt Block Road / Shortway / Breakup Protection Logic Action
Motion of work . Step / ActionCross-reference
StepsActions
⑦MI, the protective shield continues to withstand high temperature and pressure, and remains structurally stable.
03

PRODUCT STRUCTURE

Product structure

3.1 MI Integration structural level

3.2 Exterior specification (6 types)

3.3 Temperature structure type

3.4 Output mode

Analysis of strengths and weaknesses

4.1 Main advantages

4.2 Main shortcomings

Pt Temperature Component

Functional description: platinum electrical resistance core, temperature induction core Usage material/specification: Pt100 / Pt1000 / Pt50 / Cu50

MGO Insulation

Functional description: Electrical insulation + Thermal conductor + Mechanical buffer Usage/Specific: Magnesium peroxide high purity ≥ 99.5%

Metals.

Functional description: Mechanical strength + Air-mass protection + Corrosion resistant Usage/Specific: 316L / 310S / Inconel 600 / 825G

Inline

Functional description: Resist cores are drawn out to the end of the line Common material/specifier: pure nickel / nickel chromium / silver plating copper / nickel plating copper

End Seal

Functional description: Measurement of end-air density, waterproofing of dust, common material/specification: arc welding / laser welding + caps

Seal the bridge.

Functional description: Cold-end seals extract commonly used materials/specifies: M20/NPT1/2/M27 Waterproof interfaces

Junction box

Functional description: Cold end compensation, signal transfer, common materials/specifiers: clased aluminium / stainless steel / engineering plastics

Connector End

Functional description: Compensatory guide access Usual material/specifier: nickel plating copper endpoint / ceramic endpoint

Process connection

Functional description: Installed in pipe / packagings Common materials/specifications: screws G1/G2, Frank DN25~100, active Frank

Cold-end transporter

Functional description: linear + 4-20mA + Hart / bus Usual material/specifier: Integration 4-20mA + Hart protocol

Deck / Warning

Functional description: fractional, metrical, blast-proof markings Common material/specification: stainless steel etching / laser marking

Outer

Name of component: application area Functional description: response time Usual material/specify: remarks

Φ1.0 mm

Name of component: Microreactive, Medical Experiment Description: 63 0.5s Usual Materials/Specific: Minimum Specifications, with Special Seal

Φ1.6 mm

Name of component: Biofermentation, Heating Board Function Description: 63 1.0s Usual Materials/Specific: Extremely Rapid Response

Φ3.0 mm

Name of component: Mainstream industrial processes Functional description: 63 2.5s Common material/specify: Mainstream specification, best value for money

Φ4.5 mm

Widget name: High temperature / High pressure scenario Function description: 63 4.5s Usual material/specify: General specification, higher resistance

Φ6.0 mm

Name of component: Power plant, High Temperature Pipeline Description: 63 7s Usual Materials/Specific: High Temperature, Anti-seismic

Φ8.0 mm

Widget name: special reinforcements feature description: 63 12s Usual material/specify: highest intensity, slowest response

Structure

Name of component: Structural characteristics Functional description: Response Usual material/specify: application

Naked

Name of component: measurement end without presence, welded end hat Function description: Fastest Usage/Specific: Short insert depth, low temperature rapid measurement

Indentation

Name of component: End-processed into ⁇ 1.6/ ⁇ 2.0 finer functional description: faster commonly used materials/specifies: occasions requiring local rapid response

Thread type

Name of component: Last-stroke threaded connection Functional description: medium Usual material/specifier: site-friendly scene

With a condom

Name of component: Measurement of end jacket spring protection Functional description: Slower Usual material/specify: wear-prone occasion (e.g. fluid impact)

Ceramic sealing

Structural characteristics: Pt resist + ceramic seal Response: Medium Application: Chemically resistant to corrosion

Output Type

Structural characteristics: signal form Response: load capacity Application: typical application

Resisting signal.

Structural characteristics: Pt100 18.52 ~ 390.48 Reaction: Unsourced Apply: Short-Range Read / High Precision Matrix

A second-line system 4 - 20 mA

Structural characteristics: Ringed power supply Response: RL ⁇ (V-12) / 0.02 Application: Mainstream industrial site

Four-lined 4-20 maA

Structural characteristics: Independent power circuit response: RL ≤ 600 times application: high accuracy

Hart Protocol

Structural characteristics: 4-20 MA + digit two-way response: need hand-manufacturing application: remote parameter group / diagnosis

MODBUS RTU

Structural characteristics: RS-485 Digital Communications Response: Up to 32 Nodes Application: Multiple instrument network

Field bus FF / PA

Structural characteristics: bus-type nature security Response: Essential security settings Application: Chemical DCS integration

1

Advantages: MI Integration: Temperature + Insulation + layers of protective shield, bending, damp-proof, earthquake-resistant

2

Advantages: Very quick response: ⁇ 3 mm specification t63 1 ~3 s only, far above assembly 30 s

3

Advantages: high measurement accuracy: A level ± 0.15 °C, 1/3 DIN B ± 0.10 °C

4

Advantages: high pressure resistance: metal shield tolerance 30~100 MPa pressure

5

Advantages: Strong seismicity: Depth Mgo buffers, withstand 50g vibration

6

Advantages: Bendability: minimum bend 5x exterior, adapted to complex installation space

7

Advantages: good interchangeability: Pt100 Standard IEC 60751, common scale

8

Advantages: Long lifespan: Seal structure resistant to oxidation, average life 5-10 years

9

Advantages: good linearity: Pt Resisting temperature properties close linearity, simple secondary instrument

Disadvantages and use restrictions

1

Disadvantages: Lower temperature upper limit: maximum 850 °C, inability to measure higher temperature

2

Disadvantages: Higher prices: MI process complex, approximately 1.5-3 times more than assembly

3

Disadvantages: Unrecoverable on site: damage needs to be replaced and the wire core cannot be removed

4

Disadvantages: Curve is required: repeated bends cause Mgo to decrease density, limit alert

5

Disadvantages: Response affected by external diameter: ⁇ 1.0 Responds fast but fragile, ⁇ 6+ Responds slow but durable

6

Disadvantages: Need to stimulate electricity currents: chronic large currents can cause self-heat errors

7

Disadvantages: Lead cost: 3/4 line compensation guide is more expensive than 2 line 30 ~ 50%

8

Disadvantage: high installation accuracy: precise control of depth of insertion

04

APPLICATIONS

Application area

The following conditions are widely used for such characteristics as responsiveness, long life, bendability and high stress resistance:

5.1 Typical application cases

One or more. 1000 MW Firecracker boiler for water temperature measurement

Temperature 280 ~ 320 ℃ Pressure. 25 MPa , with the t-shirt 6 Inconel 600 The suit. Pt100 + Active Frank installation, running 8 Year in use, annual cost savings on the acquisition of heat and electrical resistance 300000 (a) CNY;

Temperature monitoring of a LNG storage tank at a receiving station

-162 ℃ Deep cold, use the t-shirt. 3 316 L-Assemble Pt100 Match 4 Lined high-precision transducer, temperature monitoring accuracy ±0.2 ℃ ;

Temperature of a chemical plant polymerized in a smelting unit

Temperature 220 ~ 280 °C, high viscosy polymer melt, with a pt100 + preservative coating + Hart protocol output of ⁇ 4.5 316 L;

Some fermentation tank workshop

Temperature 30~45°C, CIP 80~95°C for cleaning, using a ⁇ 3 sanitary level 316L for Pt100 +tri-Clamp interface;

Aerodynamic thermometric test table

Temperature -50 ~ +600 ℃ ♪ Strong vibrating, using the twilight ♪ 3 Inconel 600 The suit. Pt100 +High-intensity end-container structure.

Electricity / Fire

Typical: boiler water, heater wall temperature, medium: steam / water / boiler water

Electricity / Nuclear Power

Typical: reactor core temperature for medium: reactor coolant

Chemical / petrochemical

Typical work: Reaction plume, distillation tower, polymer plume for medium: organic solvent, catalyst, polymer melt

Gas / LNG

Typical: LNG storage tanks, cryogenic pipelines for media: Liquefied Natural Gas, Liquefied Petroleum Gas

Metal / Steel

Typical: castling, heating furnaces, hot-rolling lines, representing mediums: steel, steel, water, rollers

Food / Beverage

Typical: CIP Cleaning, Bacillus Cyctomy, for media: Milk, Beer, Juice, Soy sauce

Medicine/ Biological

Typical: fermentation tanks, freezers, fungicides, for media: pharmacological, cultured, purified water

Scientific research / hot-work

Typical: test table, wind hole, heat flowometers for medium: air, oil, water vapour

Aviation / Military

Typical: engine temperature measurements, aircraft skinning, representing mediums: aviation kerosene, hydraulic fluids, air

Thermal dolls are marked.

Typical: Standard thermoelectric doll / Cold-heat constant sluices for media: Silicon oil, alcohol, water, liquid nitrogen

05

TECHNICAL SPECIFICATIONS

Technical Parameter Table

6.1 Complete machine parameters

6.2 Precision and permitted deviations

  1. 01

    Select Table

7.1 Naming rules

Typical naming rule

WZPK-2310-L1000-G1-316L-3L-Pt100

7.2 Recommendations for Common Models

  1. 01

    Selection Guide

8.1 Selective Steps

8.2 Typical Work Status Recommendations

8.3 Selective care

This is the summary of the complete technology for thermal resistance in accelerator. The actual selection should combine the process parameters, medium properties, installation methods, pressure levels, life-cycle costs, etc.

Technical Parameter Table · Parameter Category / Parameter NameCross-reference
Parameter CategoryParameter NameSpecifications
Sensor typeSensor typePt100(α=0.00385)/ Pt1000 / Pt50 / Cu50 / Ni120
Temperature rangeTemperature range200 ~ +850 ℃ by widget and shield
Accuracy classAccuracy class1/3 DIN B ± 0.10 °C/A ± 0.15 °C/B ± 0.30 °C (0 °C)
MI Outer SpaceMI Outer Space SpecificationΦ1.0 / Φ1.6 / Φ3.0 / Φ4.5 / Φ6.0 / Φ8.0 mm
Minimal bendMinimum bend radius5 x Exterior
Response timeResponse Time t63Φ3 ≤ 3 s;Φ4.5 ≤ 5 s;Φ6 ≤ 8 s
Metals.Metals, protective material316L / 310S / 321 / Inconel 600 / 825 alloy
Insulation materialInsulation materialMagnesium peroxide high purity Mgo ≥ 99.5%
QuoteQuote2 / 3 / 4
End SealEnd sealing process/ Laser Weld + Hat Seal
Cold-end sealCold-end sealing processepoxy resin / glass powder / laser welding
Insulation resistanceInsulation resistance≥ 1000 M times@100 V (extremist external shell)
Resisting voltageResisting voltageAC 500~1500 V / 1 min
Pressure resistancePressure resistanceΦ3 30 MPa / Φ6 100 MPa / Φ8 200 MPa
Anti-shock resistanceAnti-shock resistance30~50 g, 10~500 Hz (three axis)
Process connectionProcess connectionSnacks G1/G2, NPT, Frank DN25~100, Activity Frank, Carpenter
Insertion depthInsertion depth50 ~ 5000 mm, custom-made
Junction boxJunction boxAluminium / stainless steel / engineering plastic / IP65 ~IP68
Output signalOutput signalMV / 4-20 maA / Hart / MODBUS / bus
Ambient temperatureAmbient temperature40 ~ +85 °C (transmitters part)
Process medium temperatureProcess medium temperature200 ~ + 850 °C (Pt100 standard)
Explosion protection markingExplosive-proof level (optional)Ex d IIC T6 / Ex ia IIC T6
ChiefChief100~6000 mm, custom
WeightWeight0.1 ~ 3 kg (depending on specifications)
Accuracy classGrant (°C)Grant(s)@0°CApplications
1/3 DIN B±0.10±0.04Measurement level, key controls
Technical parameter table . Precision / bellow (°C)Cross-reference
Accuracy classGrant (°C)Grant(s)@0°CApplications
Level A±0.15±0.06High-precision industrial site
Level B±0.30±0.12General Industrial Site
Level C±0.60±0.23General temperature measurements
Technical parameter table . Part bit / codeCross-reference
PartCodeMeaning
1WZPKPlatinum resist (Z for resist/K for tatter/ P for platinum)
22Line box form (2=splash/ 3=waterproof / 4= explosion / 5= Benn)
33Hat (3=normal / 5=sanitary / 7= ceramic seal)
41Exterior specification (1= ⁇ 3 / 2 = ⁇ 4.5 / 3 = ⁇ 6 / 4 = ⁇ 8)
50Installation (0=snix / 1=Franco / 2=ActiveFranc / 3=Class)
6L1000Insert depth L+ value (mm)
7G1Process Connection (G1 / G2 / DN50, etc.)
8316LMetals protective material (316L / 310S / Inconel 600)
93LLines 2L = 2 / 3L = 3 / 4L = 4)
10Pt100Fractional (Pt100 / Pt1000 / Cu50 etc.)
Technical Parameter Table . Serial Number / ModelCross-reference
Serial numberModelSpecifications DescriptionTypical applications
1WZPK-2310-L1000-G1-316 L-3L-Pt100Load / Splashbox / ⁇ 3 / G1 / 1m / 316L / 3Main industry specifications
2WZPK-2320-L1000-G1-316 L-4L-Pt100-ALoad / Splashbox / ⁇ 4.5 / G1 / 1m / 316L / 4 Line / A LevelHigh-precision industrial site
3WZPK-4320-L1500-DN50-I nconel600-3L-Pt100Load / Waterproof Box / ⁇ 6 / NN50 / Inconel 600 / 3High temperature, high pressure, corrosive medium
4WZPK-2310-L500-M27-31 6L-3L-Pt100-1/3BLoad / Splashbox / ⁇ 3 / M27 / 316L / 1/3 DIN BMeasuring key control points
5WZPK-2310-L800-G1-310S -3L-Pt100Load / Splashbox / ⁇ 3 / G1 / 310S / 3Power plant boiler water / high temperature steam
6WZPK-4310-L2000 - Activity French 825-3L-Pt100Load / Waterproof Box / ⁇ 3 / Active Fran/ 825 Alloy / 3 LineLNG storage tank cryogenic
7WZPK-2310-L1000-Tri-Cla mp-316L-3L-Pt100Load / Splashbox / ⁇ 3 / Tri-Clamp / Sanitary 316L / 3Food / Pharmaceutical Health Level
8WZPK-7310-L500-M20-31 6L-4L-Pt1000-IALoad / Detonator / Detonator 3 / M20 / 316 L / Pt1000 / Ex iaThe bombproofing Ben Ann field bus.
9WZPK-2310-L1500-G2-316 L-3L-Pt100-WirelessLoad / Splashbox / ⁇ 3 / G2 / 316L / Wireless HartHigh-altitude slots for inconvenient wiring
Technical parameter table · Step / Selective considerationCross-reference
StepsSelection
①Confirm temperature range: lowest / maximum temperature Selected fraction number (Pt100/Pt1000/Cu50)
②Confirm accuracy requirements: ± 0.1 °C to select 1/3 DIN B; ± 0.3 °C to select B
③Confirm the corrosivity of the medium: weak corrosive selection 316L; strong corrosive selection of Inconel 600/825 alloy
④Identification of response requirements: quick response selection ⁇ 1.6/ ⁇ 3; high intensity selection ⁇ 6/ ⁇ 8
⑤Confirm pressure level: High pressure selection ⁇ 6+; low pressure can be ⁇ 3
⑥Determine the thread system: Normal 3 lines; High precision 4 lines
⑦Select process connection: screw / Frank / Active Frank / Health
⑧Select output mode: mV / 4-20mA / Hart / MODBUS / bus
⑨Determination of blast level: by hazard area (Zone 0/1/2) selected Ex ia / Ex d
⑩Accounting for life costs: integrated procurement + maintenance + security risks
Technical parameter table . Work / TemperatureCross-reference
WorkTemperatureMediaRecommended SpecificationsKey parameters
A boiler.280~320High pressure deoxygeneWZPK-2310-L500-G1-310S-3L-Pt 100⁇ 3 / 310S / 3 line / Pt100
LNG storage tank162Liquefied natural gasWZPK-4310-L2000 - Activity Frank 825-3L-Pt100⁇ 3 / 825 Alloy / 3 Line / Pt100
Synthetic Cyclops220~280Polymetallic MeltWZPK-2320-L1000-G1-316L-4L-P t100⁇ 4.5 / 316L / 4 Line / Pt100
Frozen dryer40~+50Medicine.WZPK-2310-L500-G1-316L-4L-Pt 100-A⁇ 3 / 316L/4 Line / A
CIP Purge80~95AlkalineWZPK-2310-L500-Tri-Clamp-316 L-3L-Pt100⁇ 3 / Health level / 316 L
Aviation engines50~+600Air keroseneWZPK-2310-L300-M20-Inconel60 0-3L-Pt100⁇ 3 / Inconel 600 / Reveal
Catalyzed fragmentation480~520Gas + CatalystWZPK-4320-L800-DN50-Inconel6 00-3L-Pt100Φ6 / DN50 / Inconel600
Standard platinum resistance0Silicon oil hottruckWZPK-2310-L500-M27-316L-4L- Pt100-1/3B⁇ 3 / 1/3 DIN B / 4
Thermal dolls are marked.50~+660ValidatorWZPK-2310-L500-G1-310S-4L-Pt 100-A⁇ 3 / 310S / 4 Line / A Level
Technical parameter table . Work / TemperatureCross-reference
WorkTemperatureMediaRecommended SpecificationsKey parameters
Reaction cold.100~+20 0Organic solventsWZPK-2310-L1000-G1-316L-3L-P t100⁇ 3 / 316L / 3
Serial numberAttention
1Temperature range should reserve ±10% surplus to avoid being in full range for a long period
2Select 4-line system when precision is high + A or 1/3 DIN B
3Inconel 600 / 825 alloys should be preferred for the strong corrosive medium
4The selection of Pt1000 at low temperature depth colds (< -100°C) can provide a higher sensitivity.
5Self-heating error is not negligible: Incentive current ≤ 1 mA appropriate
6A curved radius may not be less than 5 times the outer diameter and bend once unrecoverable
7The following fine lines are to be selected for the vibration scene: ⁇ 6/ ⁇ 8 specification, to avoid fractures in the following ⁇ 3
8Process thread too tight could cause MGO to burst, and should use a twister.
9Periodic calibration: recommended standard resistance ratio for every 6-12 months
10Transport installation needs to be particularly sensitive: cable-mounted cables are easy to bend and small radiuss are avoided