PRODUCT TECHNOLOGY

Non-resulting steel sheet pressure table

Operating principle

The stainless steel sheet pressure sheet.

The use of a hyphenation box as a sensitive element for measuring micropressures is another technical route that parallels the flex pressure table with the spring tube (boden tube) and specializes in micropressure/negative pressure ranges. When pressure (or negative pressure) of the detector medium acts on the inner cavity of the membrane box, the free end of the membrane box produces the corresponding elastic deformation (place shift), which is amplified by the gear-driven gear transferer, and the measured pressure value is indicated on the pallet by the pointer fixed to the gear axis. (a) The membrane box is made of two round-shaped wave-line film pieces welded along the perimeter (in stainless steel, plasma welding/laser welding): the inner cavity is sealed and vacuumed or filled with a specific gas; The ripple structure allows the film to have a very low degree of rigidity in the axis, and a very small pressure can produce a larger arctic shift (well more sensitive than the spring tube); Use multiples when individual membrane slots are insufficient

  1. 01

    Rate applicable 0.1 MPa (100 kPa) ~ 160 MPa 0.25kPa ~ 100kPa

  2. 02

    The sensitivity of the transducer is low, high, very high.

  3. 03

    Overpressure power, stronger, weaker.

  4. 04

    Application of medium · Gases, liquids = Gases only (micropressure)

Support for stainless membrane box pressure table selection

Provide survey missions, media and installation conditions and obtain product configuration advice.

Contact us
The stainless membrane box pressure table.

TECHNOLOGY & APPLICATION

Understand the principles, the exact selection.

From measurement principles to field applications, the technical characteristics and selection elements of the stainless steel sheet pressure table are understood.

01

MEASUREMENT PRINCIPLE

Measurement principle

The use of a hyphenation box as a sensitive element for measuring micropressures is another technical route that parallels the flex pressure table with the spring tube (boden tube) and specializes in micropressure/negative pressure ranges.

1.1 Rationale

When pressure (or negative pressure) of the detector medium acts on the inner cavity of the membrane box, the free end of the membrane box produces the corresponding elastic deformation (place shift), which is amplified by the gear-driven gear transferer, and the measured pressure value is indicated on the pallet by the pointer fixed to the gear axis.

The entire measurement and instruction process was entirely mechanical and did not require external power supply and was essentially a security instrument.

1.2 MEmbrane Box Sensitive Component

(a) The membrane box is made of two round-shaped wave-line film pieces welded along the perimeter (in stainless steel, plasma welding/laser welding): the inner cavity is sealed and vacuumed or filled with a specific gas;

The ripple structure allows the film to have a very low degree of rigidity in the axis, and a very small pressure can produce a larger arctic shift (well more sensitive than the spring tube);

Where individual membrane box slots are insufficient, multi-film box cascades can be used to further increase the degree of shift and sensitivity.

1.3 Nature of difference with spring tube (Boden tube)

The lower range of the springbarometer is usually 0~0.1 MPa (i.e. 100kPa) and does not cover the measurement needs of the boiler ventilating, chamber pressure etc., kPa level - this is the value of the membrane box pressure sheet.

The principle of measurement . Contrast / spring tube (Bordone tube)Cross-reference
ComparativeSpring tube (Bordone tube)Menm Box
Application of the scale0.1MPa(100kPa)~ 160MPa0.25kPa ~ 100kPa
Offset SensitivityLow (large core magnification ratio required)High (micropressure is a significant shift)
OverpressureStronger.Weakness (overpressure prone to permanent deformation)
Suitable mediaGases, liquidsGas limit (micropressure)
02

PRODUCT STRUCTURE

Structure

The instrument consists of four main parts of the measurement system, the moving apparatus, the instructional parts and the outer casing.

2.1 Measurement systems

Connect.

The normal type is brass HPb59-1; stainless steel is sus 316,22mm quadrilateral, screw M20x1.5 (detailable);

Membrane Box (Sensitivity Component)

The normal type is tin copper QSn6.5-0.1 double metal membrane boxes, welding; stainless steel preservatives are SUS 316 double film boxes, plasma welding/laser welding, and corrosive resistance and welding reliability are significantly increased.

2.2. A moving institution

Dial up the pole.

Converts the straight-line position of the free end of the filmbox to an agular shift;

Gear transfer facility (core)

The normal type is copper alloy cores, the preservative type is stainless steel cores, and mechanically magnified the small agular position.

2.3 Indicating parts

Pointer and Tray

Aluminium black-bed tics (specially processed);

Micro-motion zeroer

Most model labels (be located outside the dashboard) allow for easy on-site adjustments to the instrument zeros - the membrane box types are modified by temperature drift and creeping, and the Zeros are routine routine routines.

2.4 Shells

(a) The shell, the lining and the glass of the watch acts as protection, support and installation;

Normal type (YE)

Cold-rolled steel plate black plastic (ST13); embalming type (YEF): SUS304 stainless steel (paintable) with a protection level of IP54;

Table glass is 3 mm flat glass (option 4 mm or blastproof glass).

2.5 Form of installation

The instrument shall be vertically installed in many forms, including the sideless, the back-banded (TQ), the axis-sided (Z), the front of the axis-belt (ZT).

2.6 Model spectrometry

Evolution

Model Character

Base

YE-60 / 100 / 150 Copper Alloy Steering System + Steel Crust Spraying to measure non-corrosive gas micropressure of copper alloy

Preservative type

YEF-100/160 Total stainless steel (316 join head/ membrane box + 304 shell), high corrosion resistance

Imbrane Box stainless steel

YTFE-60~150 Pressure system and shell using 1Cr18Ni9 stainless steel

Pumpkin.

YEF-100-B/Z-B radial/axis variant, range to ±30kPa, 60kPa

03

TECHNICAL GUIDE

Advantages and disadvantages

3.1 Advantages (10 items)

Micropressure measurement capability is strong

The lower limit of the range is as low as 0~1.6 kPa (0.25 kPa starting range of the ⁇ 160 type) and is an area that cannot be covered by the springbarometer;

Very sensitive.

The wavering box produces a significant shift at a small pressure, which is coupled with the magnification body to achieve a KPa class resolution;

Persistible negative pressure and positive negative pressure

(b) Provide -X~0 (negative pressure), -X~+X (pressure vacuum entanglement), and complete the work schedule for the chamber, etc.;

No power, no security.

(b) purely mechanical structures, which are natural for on-site instructions in blast-proofing situations;

Read it in person, observe it.

(a) A tablet instruction, not dependent on secondary instruments;

The stainless steel-preservative environment is adaptable.

(a) SUS316 + SUS304 crust + IP54, which can be used for humid corrosion;

With a micro-motion zero.

On-site, zero-displacement modifications and maintenance facilities;

Simple structure, low price.

(a) Far below the micropressure deliveryer, which is a low-cost option for micropressure indications;

Partially model banded-in structures

(b) Curveding of a pointer that inhibits pressure pulses (practical flue flow in the event of ventilation);

Installed in full form

Arc/axis/side multi-specification, vertically installed, without conditions such as direct tube segments.

3.2 Limitations (10 items)

Low limit of the scale

(b) For general to 0~40/60 kPa (individual to 100kPa), the spring-line pressure sheet shall be replaced by 0.1 MPa or more;

Only for gas media

(b) Membrane box systems are designed for micropressures of gases and cannot be measured for liquids;

We're weak at overpressure.

(b) The film box is subject to permanent deformation and even rupture after overpressure, leaving sufficient amount of the selection to avoid shock pressure;

Low Precision

Level 2.5 (optional 1.6) is far below the carrier and cannot be used to measure the settlement;

The temperature effects are more pronounced.

(b) An additional temperature error of about 0.4%/10°C at the time of deviation from 20 ± 5°C, with significant errors in high-temperature-volatile environments;

Low range of ambient temperature used

-25 ~ 55℃, relative humidity ≤80%, restricted in high temperature, high humidity;

Resilient capacity is normal.

V.H.3 Level, hand-held, core-repeated, with a high vibration setting, with a choice of seismic-resistant variant or a change of programme;

No signal is passing far.

(a) purely mechanical instructions, which do not allow access to DCS/PLC, and which must be transferred to micropressurizers;

The film box has fatigue and creeping.

(a) Flexic properties drift under long-term concussion pressure, subject to periodic review (based on JJG 52/ corresponding review protocols);

Powder, crystal and viscous media

Small pressure holes, dust plugs, medium crystals, which directly cause failure, and dirty gases must be filtered/blowed.

Device.

04

APPLICATIONS

Application area

4.1 Typical application scenarios

4.2 No work conditions and alternatives applied

Area

Typical performance.

Boiler/combustion unit

Boiler negative pressure monitoring, wind-release pressure 0.4-0, 0~2.5kPa

Heating air conditioners (HVAC)

Wind pipe static pressure, filter pressure differential indicator 0~1.6/2.5kPa

Gas systems

Micropressure, motorizing 0~6/10kPa for gas pipelines

Ventilating and dusting.

Wind wind pressure, dedustor resistance 0~4~16kPa

Chemical/metal corrosive gases

Corrosive gas micropressure/negative pressure (select YEF fully stainless steel) 0~25~60kPa

Laboratory/laboratory equipment

Leaching negative pressure, gas flow monitoring 40~0kPa

Environmental governance

Pyrotechnic micropressure, spray tower pressure differential ±2 ~ ±20kPa

Not applicable

Recommended replacement

Liquid media pressure

Spring tube pressure table (normal/retainless steel)

>0.1MPa pressure

Spring tube pressure table

Vibration environment

Stun-resistant pressure table (YBN series) or micro-disklifter

Remote transfer/closed loop control required

Microvoltage/disklift deliveryer (e.g., single-crystal silicon)

High precision measurement

Digital micropressometers or micropressure transmitters

Dust/crystal gases

Add dust filters or switch to long-forward nuclei programme

05

TECHNICAL SPECIFICATIONS

Technical Parameter Table

5.1 Overall technical parameters

5.2 Slotting scale of scale (YE/YEF-100/150)

Technical parameter table · Item / ParametersCross-reference
ItemParameters
Applicable standardsJB/T 9274-1999 (Medinal Box Pressure Sheet)
Normal diameterΦ60、Φ100、Φ150(Φ160)
Accuracy class2.5 Level (1.6 level optional, 150/160 better)
Scale range- Right on. 0 ~ 1.6 to 0 ~ 60kPa (Φ 160 - I'm not sure. 0 ~ 100kPa ;negative pressure -1.6 ~ 0 to -40 ~ 0kPa ;United Nations -0.8 ~ +0.8 to -20 ~ +20 ( ±30 )kPa
Ambient temperature25~55℃
Relative Humidity≤80%
Temperature Additional Error≤0.4% / 10℃ (when deviating from 20 ⁇ 5℃)
Work environment resistanceV.H.3 Level
Ingress protectionstainless steel preservative IP54
Connection ThreadM20x1.5 (as-needed), 22mm squared
Mountingvertically installed;reverse/axis/sides in many forms
Sensitive shapesSUS316 Double-wielding membrane box (plasma welding/laser welding)
Review BasisJJG 52 (Clindrum-type general pressure table control protocol applied by reference)
Technical parameter table . Positive pressure (kPa) / Negative pressure (kPa)Cross-reference
Positive pressure (kPa)Negative pressure (kPa)Positive and negative pressure (kPa)
0~1.61.6~00.8~+0.8
0~2.52.5~01.2~+1.2
0~44~02~+2
0~66~03~+3
0~1010~05~+5
0~1616~08~+8
0~2525~012~+12
0~4040~020~+20
0~60 (individual to 100)—30~+30
Technical parameter table · Model / StructureCross-reference
ModelConstruction% PrecisionWeight kg
YE-100 / YE-150♪ The way to the side±2.5 (±1.6 optional)~0.5
YE-100Z / YE-150ZAxes unbounded.±2.5—
YE-100TQ / YE-150TQBottom mount with rear flange±2.5—
YE-100ZT / YE-150ZTAxebelt front±2.5—
YEF-100 / YEF-160Total stainless steel preservation (316 membrane boxes)±2.5 (1.6 optional)—
YTFE-60~150Pressure system and shell complete 1Cr18Ni9±2.5—
PartsYE NormalYEF Preservative
Connect.Copper HPb59-1 (enabled plating)SUS316 Beneath, 22mm square
Menm BoxTin Bronze QSn6.5-0.1 SylverSUS316 Double film box, plasma welding/laser welding
Machine coreCopper alloystainless steel.
ShellST13 BlackjetSUS304 Body Colour (Putable)
Glass.3mm flat glass3mm flatboard (option 4mm/explosive)
06

SELECTION GUIDE

Select Table

6.1 Required parameters for ordering

  1. 01

    (a) The name of the detected medium and its corrosivity (gas; dust/crystal/clubber;

  2. 02

    Measurement range (positive/negative/joint, kPa) and constant working pressure values;

  3. 03

    Whether there is vibration, pulse;

  4. 04

    Temperature, humidity and corrosive atmosphere in the environment;

  5. 05

    Table radium (squadium) 60 / 100 / 150 / 160 );

  6. 06

    (a) The form of installation (repeated/axis/side) and the direction of the installation;

  7. 07

    (a) Link screw specification (default M20x1.5);

  8. 08

    Precision requirements (2.5 level, 1.6 level fixation);

  9. 09

    Need for zeroing and blockage structures.

6.2 Material selection

6.3 The rules for the selection of the quantum course

Positive pressure measurement

The maximum work pressure falls on the scale. 1 / 3 ~ 2 / 3 (b) Be appropriate;

Negative pressure/joint measurement

Ensure that work points are in the middle of the scale to avoid long-term discounting or fullness;

Overcrowding is the first principle.

(b) A film box with weak overpressure capacity, with a fluctuating work schedule that is floating up and, if necessary, a series of buffer/pressure devices;

Example:

The chamber has a normal load pressure - 200 Pa, fluctuations - 600 Pa ⁇ Selection - 1.6~0kPa or -2~2+kPa (about 12% ~37% full capacity at the work point and remaining at the residual level).

6.4 Table & Precision Selection

6.5 Example of Model Preparation (YEF series)

Technical IconClick to see the big picture
YEF - 100 Z T Q - B
♪ ♪ The world is so full of shit ♪
⁇ ⁇ - with side (tQ behind / ZT front, no margin omitted)
Zulu-----Axis (Z), abbreviation
Table of income and expenditure by region (A/60/100/150/160)
– – – – Pressure table for the fully stainless steel preservative film box

6.6 Selective elements and use maintenance

  1. 01

    First, we'll confirm the micropressure.

    > 100kPa without membrane table; in the medium for liquids without membrane table;

  2. 02

    Slow down the valves, protect against shocks.

    (b) The valve shall be slowly opened for use and pressure shock membrane boxes shall be strictly prohibited;

  3. 03

    (a) Vertical installation to take over as short a time as possible and avoid saping fluids;

  4. 04

    Regular zeroing

    (b) Zeroing of depressures, using external zeroing;

  5. 05

    Periodicity Check

    (b) Conduct inspections in accordance with the protocol cycle, focusing on the verification of the muscularity and delay of the membrane box over the standard;

  6. 06

    Dirty gas with filters

    Dust, tar gas shall be filtered and regularly blown to prevent congestion of the conductor hole;

  7. 07

    Temperature correction awareness

    Additional errors estimated for environmental deviations from 20 ⁇ 5℃ at 0.4% / 10℃;

  8. 08

    Do not replace the transmitter with the deadline.

    Directly select micropressure/disk Transmitters for control, locking, and tele-send needs.

Selective Table . Work Situational Assessment / Recommended ModelCross-reference
Work situation judgementRecommended ModelAnnotations
Air, nitrogen, etc., are not corrosive to copper alloysYE NormalMinimum cost
Corrosive gases (acidity, dampness, ocean atmosphere)YEF / YTFE Total stainless steel316 Membrane Box + 304 Shell, IP54
Strongly corrosive medium and dusty crystalThe membrane sheet is not applicable.Change diaphragm seal + Remote Transfer
Selective Table . Tables / CharacteristicsCross-reference
Table PathCharacteristicsApplication
Φ60LightweightEquipment packages, space limitations
Φ100Standard size, genericMain selection for on-site surveillance
Φ150/160Scale long, read accurate, with a choice of 1.6 and lower starting range (0.25 kPa)Critical sites, laboratory verification
07

TECHNICAL GUIDE

Horizontal comparison table

7.1 Membrane box pressure table vs proximity meters

7.2 Selective mouthpieces

Micropressure negative pressure search film box, gas-specific insulated fluid; One-third range, three times above pressure, with residual pressure; Corrosion wet and wet, full steel, dust crystals and filters; Remote, precision, micropressure deliveryer.

The technical parameters of this summary are based on the public samples of JB/T 9274-1999 and mainstream manufacturers (Tiensang, Control, Novo, etc.), which are based on the latest samples from the manufacturer.

Table of horizontal comparisons · Contrast / stainless membrane box pressure table (YEF)Cross-reference
Comparativestainless steel membrane box pressure table (YEF)Common springbarometer (Y)stainless steel diaphragm pressure table (YTP)Micropressure/disconnectors
Sensitive shapesBlanche Membrane BoxSpring tube (Bordone tube)diaphragm + seal fluidCapable/single-crystal silica film
Measuring span0.25 ~ 100 kPa (micropressure expertise)0.1~160MPa0~100MPa0.1 kPa ~ Number MPa
Measurable mediaGasesGases, liquidsStrong corrosive, sticky, crystal-friendly mediumGas/liquid (vision model)
Precision2.5 Level (1.6 optional)1.6~2.5 Level1.6 Around the scale0.075~0.2%FS
TeleportationNoneNoneNone (mechanical)4~20mA/HART, formula
ElectricityNo need.No need.No need.24VDC required
OverpressureWeak (felter)StrongStronger.- Yeah. - Yeah.
ResilientV.H.3GeneralGeneralStrong
Temperature effects0.4%/10℃0.4%/10℃0.1%/°C (with sealed fluid)♪ Integration soft, tiny ♪
PriceLowMinimumMedium height (3-10 times normal table)High (multiple)
Typical usesBoiler pressure, wind pipe micropressure.General pressure field instructionsForced corrosive medium measurement pressureControl systems, precise measurements