Hammer BitmeterClick on the picture to zoom in.
PRODUCT SPECIFICATIONS
LISEN-WT-100
Hammer Bitmeter
Hammer-style material bitometers, hammer-type material bitmeters
01
Classification: remouldered bit count
02
Check configuration based on field work
TECHNICAL SPECIFICATIONS
Technical specifications
Check the specifications against your operating conditions and use the selection tables to confirm your order configuration.
View selection tables ↓| Model | LISEN-WT-100 |
|---|---|
| Measurement principle | Heavy hammer detection: the power-laying cord reduces the hammer, the tension of the rope is reduced (weight loss detection), the length of the rope is recorded by the encoder at the height of the material, and the hammer is automatically recovered |
| Measurement range | 0–10m / 0–20m / 0–30m / 0–40m (line long) |
| Measurement accuracy | ±1cm (±0.5%FS, repeatability ±1cm |
| Measurement cycle | Single measurements 30–180s (press range), with automatic intervals (1–1440min) or external signals triggered |
| Method of measurement | A single manual/time automatic/time-on-board command trigger; tape track and hammer-proof logic |
| Display type | LCD LCD Display material level height/percentage/line length, field key Configuration |
| Suitable materials | Powder, particulates, blocks (cement, dust, grain, fodder, plastic particles, mine powder, limestone, etc.) |
| Material temperature | -40–+150℃ (high-temperature type to +250℃ with an insulation seat) |
| Ambient temperature | -40~+70℃ |
| Operating pressure | Frequent pressure (open silos/ silos/ash storage) |
| Mounting | The top Flange /stretch is installed vertically, and the hammer naturally falls into the warehouse (the tilted wall needs a steering tube) |
| Plumb weight material | 304 stainless steel / 316L / PUR packaging (adulsive, wearproof) |
| Cable material | φ3 stainless steel wire rope (standard 30m) / nylon cord (static material Optional) |
| Motor / drive | Step-in generator + self-lock snail snail, with overload protection and block protection |
| Output signal | 4–20mA (composite bit height) / RS485 (MODBUS-RTU) / voltage-free dry contact ×2 (high/low Alarm) |
| Power supply | 220VAC (standard) / 24VDC (Optional) |
| Ingress protection | IP65 / IP66 (control box), hammer section IP67 |
| Explosion protection marking | Ex d II B T4 Gb (dust/gas blastproof type Optional) |
| Applicable standards | GB/T 28474 / JB/T 12597 / GB 3836.1 |
| Product features | Direct contact surface measurements, not affected by Dielectric constant, dust, steam, surface shape (cone/slanted); Accuracy stable, suitable for large Range deep |
| Typical applications | Continuous monitoring and stock measurement of material levels in cement/powder ash banks, food silos, feed silos, plastic granules, mine powder silos, limestone/coal powder silos |
Product selection
LISEN-WT-100| Code | Measurement range (cable length) |
|---|---|
| L1 | 0~10m |
| L2 | 0~20m |
| L3 | 0~30m |
| L4 | 0–40m (Specify when ordering) |
| Code | Method of measurement |
|---|---|
| T1 | + manual single time (Standard) |
| T2 | External signal/top trigger measurement |
| T3 | Multiware centralized control (1 machine control 1–8 warehouse) |
| Code | Plumb weight material |
|---|---|
| W1 | 304 Stainless steel (Standard) |
| W2 | 316L Stainless steel (reserve) |
| W3 | Polyurethane packaging (adulsive/ wearproof) |
| Code | Cable material |
|---|---|
| R1 | φ3 Stainless steel wire rope (Standard) |
| R2 | Nyron rope (static/explosive material) |
| Code | Output signal |
|---|---|
| O1 | 4–20mA (Standard) |
| O2 | RS485(MODBUS-RTU) |
| O3 | 4–20mA + 2 road relays (high and low Alarm) |
| Code | Power supply |
|---|---|
| S1 | 220VAC (Standard) |
| S2 | 24VDC |
| Code | Explosion protection marking |
|---|---|
| X1 | Non-Ex |
| X2 | Dust/gas flameproof Ex d II B T4 Gb |
| Code | Mounting accessories |
|---|---|
| A1 | Basetop Flange Installer (Standard) |
| A2 | Stainless steel steering tube (slanted silos/silos) |
| A3 | Insulation set-up (high temperature silos) |
Confirm specifications and ordering options
Contact us with the measurement target, operating conditions, and installation requirements to confirm your configuration.
Contact us