Smart Multi-Pilot Tour Display ModemClick on the picture to zoom in.
PRODUCT SPECIFICATIONS
VISCON-DIS-200
Smart Multi-Pilot Tour Display Modem
Smart Multi-Performer Touring Modem, Smart MultiPerforming Modem
01
Classification: Smart multi-point tour monitor
02
Check configuration based on field work
TECHNICAL SPECIFICATIONS
Technical specifications
Check the specifications against your operating conditions and use the selection tables to confirm your order configuration.
View selection tables ↓| Model | VISCON-DIS-200 |
|---|---|
| Product function | 8–64 spot-by-point Display and Alarm will be automatically tested in sequence, and will be replaced by a manual spot-by-point copying form; and will be capable of lock-in, Alarm memory and Channel calculations, Optional with Control output closed loop control for focus sites |
| Scan points | Standard 8 Dot. optional 16 / 24 / 32 / 64 dots; all stations share a high set accuracy A/D and cold junction compensation, by low thermoelectric EMF Scanning for change of concern (remote) thermoelectric EMF ≤0.5μV) |
| Input type | RTD Pt100 / Pt1000 / Cu50 / Cu100; thermocouple K / E / J / T / N / S / R / B; direct current 4–20mA / 0–20mA; direct current voltage 1–5V / 0–10V; resistance 0–400Ω; point-by-point type may vary (Configuration) |
| Measurement accuracy | ±0.2%FS (straight current signal); RTD ±0.2%FS (Pt100 chiev ±0.1℃); thermocouple ±0.2%FS cold junction compensation error ±1℃; scanned switch exposure to electrical resistance ≤50mΩ |
| Scanning speed | Stay 0.2–5.0s is available; full circuit cycle automatically calculated and Display; two modes of running can be used for travelling/ fixed points, moving manually or typing points directly at fixed points |
| Display unit | Standard Double Platoon 4 bits LED: Up row display Bits (Pilots) P01–P64 Downstairs display (a) the measure value and unit of the point, with additional point state indications; optional 5 Inch liquid crystal, side screen. display 8–16 Sticky Charts and Hypermarks |
| Function Alarm | Every point 2 Group alarm (ceiling, floor), total 128 Groups; alarm Delay 0–999s available; available alarm Memories, heads up. alarm Memory (recording points and moments above limit); relay output 8 Lou, Configurable For any reason. Alarm |
| Channel calculations | Supports maximum, minimum, average, ultra-point statistics for all sites, as well as margin values of any two points (e.g. temperature differential for the chamber); calculation results can be used as virtual points Display and Alarm |
| Control output | Optional 1–4 road 4–20mA or bit output performed PID reconciliation of assigned points; the rest of the stations remain on the road Display |
| Recording functions | Optional inline 8GB to record all points of historical data at set intervals, and to support point-to-point query curves and export CSV |
| Print Interface | Optional RS232 / TTL print interface to support time printing (class/day) and call printing (current mobile value + Alarm state), with a microstring printer |
| Communication interface | RS485 (Modbus RTU from station) standard; optional Ethernet; all points can be read on a one-time basis, round ≤1s |
| Power supply | AC 85–265V (50/60Hz It's a lot of work. ≤15VA; optional DC 24V |
| Enclosure and protection | Disk assembly 160×80mm transverse structure, front plate protection IP65, back line end IP20; spot endpoints arranged by serial-numbered partitions with markers |
| Panel cutout dimensions | 152 × 76mm (wide × high), insertion depth ≤190mm |
| Instrument weight | About 1.3kg (32 point configuration) |
| Applicable standards | JB/T 8214 (Industrial Process Control Condensator) / GB/T 34037 / GB/T 17626 (EMC) / Reference JJG 617 (Digital Temperature Indicator Verification regulation) |
| Typical applications | Thermal treatment furnaces and multipoint furnace temperature monitoring, storage tank temperature inspections, electrical and transformer round-group temperature monitoring, bakery multi-point cooling, kiln cross-section temperature distribution, cooling tanks and grain silo temperature monitoring |
| Product features | A scanned circuit covers dozens of points at a unit cost well below multiple one-way circuits; point-by-point Configuration, Thermocouple and RTD may be mixed; memory Alarm is available for ex post facto determination beyond the threshold; point differentials are calculated to yield temperature differentials directly and extra meters are saved |
Product selection
VISCON-DIS-200| Code | Number of scan points |
|---|---|
| P08 | 8 point |
| P16 | 16 point |
| P24 | 24 point |
| P32 | 32 point |
| P64 | 64 point (order) |
| Code | Input type |
|---|---|
| I1 | RTD Special (Pt100 / Cu50) |
| I2 | Thermocouple Special (K/E/J/T/N) |
| I3 | Thermocouple K/E/J/T/N/S/R/B full score |
| I4 | 4~20mA / 1~5V |
| I5 | Almighty input, point by point Configuration (Standard) |
| Code | Scanning speed |
|---|---|
| S1 | Every dot 1.0s (Standard) |
| S2 | 0.5s |
| S3 | 0.2s per dot (rapid tour) |
| S4 | 2–5s per dot (low power and long life) |
| Code | Display configuration |
|---|---|
| D1 | Double row 4 LED (point sign + measurements Standard) |
| D2 | Double Platoon LED + Point Status Indicator |
| D3 | 5 inch liquid crystal, 8–16 stick + ultra-limit mark |
| Code | Alarms and relays |
|---|---|
| A0 | Unrelay output (panel Alarm only) |
| A4 | 4 routing relays |
| A8 | 8 road relay (Configurable for one thing) |
| Code | Records and Printing |
|---|---|
| M0 | No records, no printing |
| M1 | Inline 8GB log (checkable curve, guide CSV) |
| M2 | 8GB Records + micro-drive interface (time/call printing) |
| Code | Control output |
|---|---|
| C0 | No Control output (pure inspection Display) |
| C1 | 1 4–20mA PID output |
| C2 | 2 4–20mA PID output |
| C4 | 4 4–20mA PID output |
| Code | Communication interface |
|---|---|
| T1 | RS485(Modbus RTU) |
| T2 | RS485 + Ethernet |
| T3 | RS485 + Ethernet + USB export |
Confirm specifications and ordering options
Contact us with the measurement target, operating conditions, and installation requirements to confirm your configuration.
Contact us