Smart ModemClick on the picture to zoom in.

PRODUCT SPECIFICATIONS

VISCON-TR-100

Smart Modem

Smart modem, smart signal modem

01

Classification by: Smart modem

02

Check configuration based on field work

⁇ Return Smart Modem Classification

TECHNICAL SPECIFICATIONS

Technical specifications

VISCON-TR-100

Check the specifications against your operating conditions and use the selection tables to confirm your order configuration.

View selection tables ↓
ModelVISCON-TR-100
Product functionPrecision for various bridge and passive sensors excitation supply Weak of it output signal Magnifying, filtering, linearization and standard Chemical processing, output 4–20mA / 0–10V / RS485 Send it directly. PLC, DCS or collecting cards to address the vulnerability of small signals to interference with long-range transmission
Compatible sensorsResisting variants gravity/force/train sensor (350Ω/1000Ω bridge), diffused silicon with ceramic pressure sensor (mV output), LVDT (decomposition module), Thermocouple with RTD, Hall and Magnetic Electrovelocity transducer, wet sensitivity and pressure sensitivity elements
Excitation supplyBridge pressure DC 5V / 10V programmable (load ≥350Ω, output current ≤60mA), or constant flow 1mA / 2mA (used RTD and semiconductor sensors); incentive stability ≤0.02%/℃
Input signalMvol. -30–+30mV (resolution 1μV), voltage 0–±10V, current 4–20mA, electrical resistance 0–4kΩ, frequency 0–20kHz; thermocouple -10–100mV; RTD II/III/ Four-wire
Amplification and rangeGain 1–1000 multiple programmable (by 1, 2, 5); zero points and fullness can be fined independently to support any segment Range map and Range compression
LinearizationInternal multiform assembly (up to 9 linear or 3 stylistic) allowing correction of sensor non-linearity; support for sensor sensitivity entry (e.g. 2.0000mV/V) for direct conversion engineering units
Filter0.1–100Hz (Step II), 50/60Hz trap, mean filter (1–64); inhibition of vibrations and electromagnetic interference from the field
Output signal4–20mA (load ≤750Ω) / 0–10V / 1–5V / 0–5V toggle; optional RS485 (Modbus-RTU) Digital output and isolation relay Alarm output
Conversion accuracy±0.05%FS (23±2℃ with incentives and magnification); temperature drift ≤0.01%FS/℃; all-temperature -20–+60℃ ≤±0.2%FS
Response speedSampling rate 10/100/1000 per second; simulated output response ≤10ms (filtration closed); suitable for dynamic force and twist measurement
Special functionPeak / valley maintenance, peak capture (dynamic measurement), decorating (zeroing), unit conversion, sensor Open-circuit detection, super Range indicator; term heavy can be marked Full scale and multiple points
Isolation performanceInput - Output - communication Quadrelation; isolation voltage 1500VAC/1min; common-mode rejection ≥120dB; applicable to Variable frequency drive, servers, etc.
Configuration methodPC software with USB/RS485 Configuration, parameter electrocution; one-key tagging supported (alert/pressure automatic calculation of gain); and batch copy of supporting parameter
DisplayOptional 4 bit LED digit Display (Display project value) or take over the marker holder
Power supplyDC 20–35V (Quota 24V); single channel power ≤1.8W (bridge pressure 10V/350Ω full load ≤2.6W)
Mounting35mm standard DIN rail trucking, or plug-in box centralized installation (optional); thickness 22.5mm (single channel)
WiringPlugged screws (2.5mm2), sensor incentive/sign/shield partitions, with shielded layers attached to ground endpoints
Operating environmentTemperature -20–+60℃, relative humidity ≤95%RH (Non-condensing)
Overall dimensions22.5 × 110 × 118mm (single channel)
Instrument weight0.18kg
Applicable standardsGB/T 17626 (EMC)/ IEC 61000-6-2 / GB/T 18271 (process measurement and control device performance assessment)/ JJG 391 (power sensor)
Typical applications(b) Industrial measurement circuits for mass and distribution systems, force and twist test stations, mass collection of pressure sensors, position transfer and vibration monitoring, rotational measurements; and various types of on-site electromagnetic interference, long-range transmission of signals, non-linear properties of sensors requiring correction
Product featuresIncentives, amplification, filtering, linearization, transformations, one-in-one, with a modem replacing multiple meters; built-in sensor sensitivity and multipointing, with the change of sensors only to change parameters without having to change hardware; programmable filters and traps, with a strong interference to stabilize readings in the environment; peak capture and high-speed sampling, with a balance between static Accuracy and dynamic measurements; four-end isolation, with Variable frequency drive, no interference with server co-location installation

Product selection

VISCON-TR-100
Number of channels
CodeNumber of channels
C1Single channel (Standard)
C2Dual Channels
C3Four-channels (carded case)
Compatible sensors
CodeCompatible sensors
S1Responsive bridge (called gravity/power/twirl)
S2mV output pressure sensor
S3RTD / Thermocouple
S4Ether / LVDT
S5Frequency / Turn speed
Excitation method
CodeExcitation method
E1Bridge pressure 5V / 10V programmable
E2Constant flow 1mA / 2mA
E3E1 + E2 switchable (Standard)
Output signal
CodeOutput signal
O14–20mA (Standard)
O20~10V / 1~5V
O3RS485(Modbus-RTU)
O44–20mA + RS485 + Alarm Touch
Accuracy class
CodeAccuracy class
A1±0.05%FS (Standard)
A2±0.1%FS
A3±0.02%FS (high Accuracy, order)
Sampling speed
CodeSampling speed
R110 sec/s
R2100 sec/ sec (Standard)
R31000 sec/s (dynamic measurements)
Special function
CodeSpecial function
F1Basic type (magnification + transformation)
F2F1 + multipoint linear calibration
F3F2 + Peak/Valve maintained
F4F3 + Peak capture and decorate
Structure with Display
CodeStructure with Display
M1DIN rail 22.5mm No display
M2DIN rail + 4 LED Display
M3Boxes (multi-channel centralized)

Confirm specifications and ordering options

Contact us with the measurement target, operating conditions, and installation requirements to confirm your configuration.

Contact us
VISCON-TR-100 Smart Signal Conditioner